A Place For Gamers By Gamers


You are not connected. Please login or register

View previous topic View next topic Go down  Message [Page 1 of 1]

#1
 Ŧг๏รtאץเ

avatar
Founder
Founder
This is a guide for those that have bricked their PS3, and don't have a valid bios backup. 
The truth is you cannot unbrick without a valid bios backup. So what you have to do is get one.
I know your probably thinking "but my PS3 won't turn on" or "but my PS3 is bricked, how can I get a valid dump?"
Well, the answer is, you can still get a valid dump from your bricked PS3.

To unbrick and you don't have a valid dump of your nor, you need to get a valid dump of the nor. Or at least a good enough one, that if it is patched with Rogero's Nor dump patcher it will be good enough to install firmware in Factory/Service mode.
So to get that valid dump follow these steps:


1. Find a pic of your motherboard [You must be registered and logged in to see this link.]. Solder a wire from nor tristate on motherboard to SBE on e3 ribbon cable. This will 2. keep your PS3 on with the first switch up on the flasher. Or you can solder a wire from nor tristate to a GND point on the 3. motherboard. Both will halt the nor and keep the PS3 on for flashing.
4. Now you need to try and get a valid backup. It is still possible even if you are bricked. Depends on what you did, and if the important info has been flashed over.
5. So to try and get some backups, keep switch 1 up, and put switch 3 up, the rest down.
6. Reseat the clip and get it on good. Or solder the e3 linker to know for sure you have a good connection.
7. Validate your backup dump. Follow [You must be registered and logged in to see this link.] to validate your dumps. I know that guide can be confusing, also look at [You must be registered and logged in to see this link.] that helped me understand how to validate my dumps. Then you can get someone with experience to double check your dump [You must be registered and logged in to see this link.].
8. After you get a good enough backup, you can patch it with [You must be registered and logged in to see this link.]. To patch it, put the bkpps3.bin in the folder with PS3_Nor_Dump_Auto_Patcher_v0.01.exe. Then drag n drop the dump onto PS3_Nor_Dump_Auto_Patcher_v0.01.exe. It will then apply the patches for you.



Click here if you still cannot get a good dump:
If you cannot get a valid dump, you can try and put one together. You will need to go through your dumps, and try and find the important info. Then use a hex editor, to put it all together. 
Go to this page: [You must be registered and logged in to see this link.]. You will need to find all the per console info. To do this you will need to search through the offsets of your bad dumps. Then compare the info with the Flash page. If you can find all the per console info, you can use a donor Nor dump for the rest of the info you need.


DO NOT CONTINUE UNTIL YOU HAVE A VALID BACKUP!!! If you try to continue without a valid backup, you may flash over the info we need to unbrick the console. If that info is not gone already.  
1. Then put switch 3 down and leave the rest as they were.
2. Flash the patched dump.
3. When it is done flashing, turn the ps3 off.
4. Put all switches down on flasher. If you soldered from nor tristate to GND instead, you need to remove the wire now.
5. Turn PS3 on and you should see the connect controller screen.
6. Then cut the power by pulling the plug or by the power switch.
7. Insert downgrade dongle into the right most USB port.
8. Plug PS3 back in, and press power then eject.
9. Wait for the dongle to communicate with the PS3 and the PS3 will shut off automatically.
10. Put [You must be registered and logged in to see this link.] (RENAME TO PS3UPDAT.PUP) and this [You must be registered and logged in to see this link.] on the root of a FAT32 formatted USB stick.
11. Replace the downgrade dongle with the USB stick, in the right most USB port.
12. Wait for about 4 or 5 minutes for the firmware to install, and the PS3 to shut off by itself.
13. Now put this [You must be registered and logged in to see this link.] by itself on a FAT32 formatted USB stick.
14. Put the USB stick in the right most USB port and press power on the PS3.
15. Wait for about 30 seconds for the PS3 to shut off by itself.


You should now be unbricked. and if you used Rogero v3.7 follow the [You must be registered and logged in to see this link.] steps.


Don't do any flashing until you get the clip on good, and get a valid dump. This is very important. If you flash over the info needed for a valid dump, it will never be recovered. Thus making your PS3 a permabrick.

Credit to playerkp420  



View user profile http://www.team-psn.net

View previous topic View next topic Back to top  Message [Page 1 of 1]


Permissions in this forum:
You cannot reply to topics in this forum

Share URL

URL Direct
BBcode
HTML